Siding Cleaners, Finishes and Sealers

Cleaners

Messmer’s Wood Cleaner and Brightener

For Cleaning Ipe, Garapa and Massaranduba Decking

Messmer’s  Wood and Deck Cleaner and Brightener (Part A and B) powder concentrates  are specially formulated to clean and brighten exterior wood decks,  fences, log homes, and other exterior wood projects.  This two-part process removes superficial dirt and grime, then removes deep tannin stains that result from extractive bleeding.  Messmer’s Wood Cleaner and Brightener is easy to use and biodegradable.

Features:

• Cleans and brightens exterior wood, removes gray and dirt
• Use before staining wood
• Excellent for deck maintenance
• Biodegradable, safe and easy to use
• Maximum strength concentrated powders
• Cleans or Brightens up to 500 square feet per 16 oz. jar
• Best results with a temperature of at least 70 degrees fahrenheit

Instructions:

Part A – Cleaner

1. Always follow manufacturer’s instructions on packaging for best results.
2. Remove dirt and debris with a broom and garden hose.
3. Mix 1/3 cup Wood Cleaner (Part A) with 1 gallon of hot water.  Mix thoroughly and let the powder fully dissolve before using.
4. Apply liberally to wood surface using a garden sprayer, mop, brush, pump sprayer, etc.  Wait 10-15 minutes, while maintaining a wet surface (a light spray nozzle on a garden hose works well).  Scrub with a stiff broom or scrub brush.
5. Rinse thoroughly with clean water using a spray nozzle and garden hose, or the lightest setting (no more than 1200 psi) on a power washer and let dry.
6. Repeat steps 1-5 if needed.

Part B – Brightener

1. For use after cleaning wood with Part A.
2. Mix 1/3 cup Wood Brightener (Part B) with 1 gallon of hot water.  Mix thoroughly and let the powder fully dissolve before using.
3. Apply Messmer’s Brightener (Part B) in the same manner to clean rinsed wood with a generous and even coat.  No need to scrub or brush this time.
4. Allow 30 minutes for color restoration.
5. Wash off thoroughly with a garden hose.
6. It is important to do BOTH parts, as Part B re-balances the pH in the wood.
7. Allow deck to dry completely before applying Messmer’s UV Plus finish.

Precautions and First-Aid:

• Product contains sodium per-carbonate.
• Maintain adequate ventilation.
• Avoid skin and eye contact.
• Wear protective gloves, eye wear and clothing.
• Skin – Wash with soap and water
• Eyes – Flush with water for 15 minutes.  Seek medical attention.
• Ingestion – Seek medical attention immediately!
• Inhalation – Get fresh air

Finishes

For Finishing Ipe, Garapa and Massaranduba Decking

Messmers UV Plus for Hardwood Decks is an oil-based product that protects and conditions hardwoods, while also maintaining a natural appearance. It has been produced with professional results in mind, providing water repellency and UV protection.

Features:

• Contains natural oils
• Alkyd resins and binders to strengthen wood against damage from the sun
• Trans-oxide pigments for longer color retention
• Natural appearance

Application:

• May be applied with low pressure spray, brush or roller
• No thinning required
• One coat application provides protection when wood is saturated
• Wood should be clean and dry before application
• Excess product not absorbed within 30minutes should be wiped dry
• Previously stained or treated wood should be sufficiently weathered to allow for complete penetration
• Decks should dry 48 hours before use
• Dispose of clean-up materials properly; allow to dry completely before use

Coverage:

• Smooth wood – approximately 200-250 square feet per gallon
• Rough wood – approximately 100-150 square feet per gallon
• Subsequent coats require less product

Clean-up:

Mineral Spirits

Colors:

Natural

Availability:

Sold by the gallon

For more product information and frequently asked questions, visit the Messmer’s manufacturer’s website.

Sealers

ANCHORSEAL2® End Sealer

End Sealer for Logs and Hardwood Lumber

ETT Fine Woods stocks ANCHORSEAL2®, a high quality wax sealer that provides protection to prevent end checking in freshly-sawn green longs and lumber.  The sooner ANCHORSEAL2 is applied after sawing, the more effective it will be in reducing end checking.

Benefits:

ANCHORSEAL2 stops most end checking before it begins.  Depending upon the species, you can prevent up to 90% or more of end checking (drying splits) and improve yield in your logs or lumber.

Application:

Anchorseal should be applied to all end grain surfaces as soon as possible after cutting.  Similar in consistency to paint, it is possible to apply ANCHORSEAL2 in several ways, including with a brush, roller, or with spray equipment.  When applied it will initially look like white paint, but will dry clear to a wax finish.  If a sprayer is used, the tip must be large enough to accommodate the thick ANCHORSEAL2 emulsion.  Care should be taken to coat only the ends of the boards.

Sprayer and application information and answers to frequently asked questions are available on the manufacturer’s website at UC Coatings.

Anchorseal should be applied liberally, “to the drip” – apply as much as the lumber will hold, until the lumber can absorb no more of hte solution.  If there is no dripping, it may be too little.  If the ends drip heavily, it is excessive.  A second coat can be applied if needed.

Availability:

Sold by the quart